Index.php
From Lane Co Oregon
| Line 1: | Line 1: | ||
| - | + | Charger : in numerous UPS systems as a result of nature of these design a separate battery charger is employed, this is more common on sub 60kVA UPS systems and is extremely common on small sub 3kVA models. | |
| - | + | Battery : this is actually the power storage area and is kept charged eith... | |
| - | + | Rectifier : this section of the UPS charging current for the battery and also the supply needs for the inverter and can converts the incoming alternating current (ac) supply to direct current (dc). | |
| - | + | Charger : in numerous UPS systems due to the character of the design another battery charger is applied, this is more common on sub 60kVA UPS systems and is very common on small sub 3kVA products. | |
| - | + | Battery : here is the energy storage section and is kept charged both by the rectifier or a separate charger. As AH (ampere hour), which will be the amount of amperes of current that the battery can provide for an hour, their storage capacity is generally exhibited. There will be a number of limiting factors depending upon the application, typically if the design calls for a small autonomy (amount of time the battery will support its weight for), the batteries may be released to a level, in the case of emergency lighting where there's a need for a autonomy the battery won't be permitted to discharge so much. These problems help permit the optimum design life of the battery to be achieved. | |
| + | |||
| + | Inverter : an ac output is provided by this section of the Uninterruptible power supply to the weight which will be in phase with the input mains supply. Because of the amount of conversions (ac to dc to ac) and the filter involved it could be termed as a 'clean source.' | ||
| + | |||
| + | Fixed Switch : this world can be as easy as a relay or even more frequently using thyristors, its goal is to move the load between the application mains supply and the inverter. So that any switching involving the two is going to be virtually seamless as has been previously mentioned the result of the inverter is in phase with the electricity mains offer. This design means that if the inverter activities an overload situation, because of its extremely fast over-current detection circuits it will move the load to the more resilient mains supply. An average example would be when a server sheet is switched on, the inrush current, based upon the size of one's uninterruptible power supplies, may cause the transfer to the utility mains supply, and after switched on the load can transfer back to the inverter offering the inverter has sufficient ability to support the load. Also a problem on the inverter may cause the load to be moved, again virtually seamlessly; it'd be unusual for just about any loss in load to happen during these conditions. | ||
| + | |||
| + | Preservation Bypass : more generally within UPS systems with a volume of 6kVA or greater. This arrangement allows force to be moved under controlled conditions to the power mains and the UPS to be power down without damage. Usually carried out for routine UPS maintenance or UPS fix. | ||
| + | |||
| + | External Maintenance Bypass : the installing of an maintenance bypass can allow the UPS to be removed/replaced without interruption to the load, also, if the actual maintenance bypass is given from another supply it can allow load testing in the case of a significant UPS repair and/or checking of the independence under simulated load situations while the site load is being recognized by the external maintenance bypass circuit. When letting the UPS System to be bypassed onto standby diesel generator power this is used. Alternatively, when batteries are changed and removed, it can only be performed by setting the uniterruptible power into outer bypass. | ||
Revision as of 00:29, 27 March 2013
Charger : in numerous UPS systems as a result of nature of these design a separate battery charger is employed, this is more common on sub 60kVA UPS systems and is extremely common on small sub 3kVA models.
Battery : this is actually the power storage area and is kept charged eith...
Rectifier : this section of the UPS charging current for the battery and also the supply needs for the inverter and can converts the incoming alternating current (ac) supply to direct current (dc).
Charger : in numerous UPS systems due to the character of the design another battery charger is applied, this is more common on sub 60kVA UPS systems and is very common on small sub 3kVA products.
Battery : here is the energy storage section and is kept charged both by the rectifier or a separate charger. As AH (ampere hour), which will be the amount of amperes of current that the battery can provide for an hour, their storage capacity is generally exhibited. There will be a number of limiting factors depending upon the application, typically if the design calls for a small autonomy (amount of time the battery will support its weight for), the batteries may be released to a level, in the case of emergency lighting where there's a need for a autonomy the battery won't be permitted to discharge so much. These problems help permit the optimum design life of the battery to be achieved.
Inverter : an ac output is provided by this section of the Uninterruptible power supply to the weight which will be in phase with the input mains supply. Because of the amount of conversions (ac to dc to ac) and the filter involved it could be termed as a 'clean source.'
Fixed Switch : this world can be as easy as a relay or even more frequently using thyristors, its goal is to move the load between the application mains supply and the inverter. So that any switching involving the two is going to be virtually seamless as has been previously mentioned the result of the inverter is in phase with the electricity mains offer. This design means that if the inverter activities an overload situation, because of its extremely fast over-current detection circuits it will move the load to the more resilient mains supply. An average example would be when a server sheet is switched on, the inrush current, based upon the size of one's uninterruptible power supplies, may cause the transfer to the utility mains supply, and after switched on the load can transfer back to the inverter offering the inverter has sufficient ability to support the load. Also a problem on the inverter may cause the load to be moved, again virtually seamlessly; it'd be unusual for just about any loss in load to happen during these conditions.
Preservation Bypass : more generally within UPS systems with a volume of 6kVA or greater. This arrangement allows force to be moved under controlled conditions to the power mains and the UPS to be power down without damage. Usually carried out for routine UPS maintenance or UPS fix.
External Maintenance Bypass : the installing of an maintenance bypass can allow the UPS to be removed/replaced without interruption to the load, also, if the actual maintenance bypass is given from another supply it can allow load testing in the case of a significant UPS repair and/or checking of the independence under simulated load situations while the site load is being recognized by the external maintenance bypass circuit. When letting the UPS System to be bypassed onto standby diesel generator power this is used. Alternatively, when batteries are changed and removed, it can only be performed by setting the uniterruptible power into outer bypass.
